remove help() from stm32 port

Author: scgbckbone

ports/stm32/help.c

@@ -26,46 +26,4 @@
 
 #include "py/builtin.h"
 
-const char stm32_help_text[] =
-    "Welcome to MicroPython!\n"
-    "\n"
-    "For online help please visit http://micropython.org/help/.\n"
-    "\n"
-    "Quick overview of commands for the board:\n"
-    "  pyb.info()    -- print some general information\n"
-    "  pyb.delay(n)  -- wait for n milliseconds\n"
-    "  pyb.millis()  -- get number of milliseconds since hard reset\n"
-    "  pyb.Switch()  -- create a switch object\n"
-    "                   Switch methods: (), callback(f)\n"
-    "  pyb.LED(n)    -- create an LED object for LED n (n=1,2,3,4)\n"
-    "                   LED methods: on(), off(), toggle(), intensity(<n>)\n"
-    "  pyb.Pin(pin)  -- get a pin, eg pyb.Pin('X1')\n"
-    "  pyb.Pin(pin, m, [p]) -- get a pin and configure it for IO mode m, pull mode p\n"
-    "                   Pin methods: init(..), value([v]), high(), low()\n"
-    "  pyb.ExtInt(pin, m, p, callback) -- create an external interrupt object\n"
-    "  pyb.ADC(pin)  -- make an analog object from a pin\n"
-    "                   ADC methods: read(), read_timed(buf, freq)\n"
-    "  pyb.DAC(port) -- make a DAC object\n"
-    "                   DAC methods: triangle(freq), write(n), write_timed(buf, freq)\n"
-    "  pyb.RTC()     -- make an RTC object; methods: datetime([val])\n"
-    "  pyb.rng()     -- get a 30-bit hardware random number\n"
-    "  pyb.Servo(n)  -- create Servo object for servo n (n=1,2,3,4)\n"
-    "                   Servo methods: calibration(..), angle([x, [t]]), speed([x, [t]])\n"
-    "  pyb.Accel()   -- create an Accelerometer object\n"
-    "                   Accelerometer methods: x(), y(), z(), tilt(), filtered_xyz()\n"
-    "\n"
-    "Pins are numbered X1-X12, X17-X22, Y1-Y12, or by their MCU name\n"
-    "Pin IO modes are: pyb.Pin.IN, pyb.Pin.OUT_PP, pyb.Pin.OUT_OD\n"
-    "Pin pull modes are: pyb.Pin.PULL_NONE, pyb.Pin.PULL_UP, pyb.Pin.PULL_DOWN\n"
-    "Additional serial bus objects: pyb.I2C(n), pyb.SPI(n), pyb.UART(n)\n"
-    "\n"
-    "Control commands:\n"
-    "  CTRL-A        -- on a blank line, enter raw REPL mode\n"
-    "  CTRL-B        -- on a blank line, enter normal REPL mode\n"
-    "  CTRL-C        -- interrupt a running program\n"
-    "  CTRL-D        -- on a blank line, do a soft reset of the board\n"
-    "  CTRL-E        -- on a blank line, enter paste mode\n"
-    "\n"
-    "For further help on a specific object, type help(obj)\n"
-    "For a list of available modules, type help('modules')\n"
-;
+const char stm32_help_text[] = "";