-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathFAQ
116 lines (94 loc) · 5.73 KB
/
FAQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
axMail - an SMTP mailbox for the various linux node frontends.
axMail appears to work with most linux based MTAs (Mail Transport Agent)
but not all, and I haven't had a chance to test it with them all either,
nor do I honestly care to install every MTA available for linux to do such
so if you do run an MTA *not listed* below, please feel free to email me
at: <[email protected]> and I'll add your report to this list. Consider this
file a 'work in progress' as with the software itself. How to test is
listed at the bottom.
PostFix - tested fine
Exim - tested fine
Smail** - failed tests, and also causes a total loss of end user mail!
Sendmail* - <unknown>
Qmail*** - <unknown>
* - In theory, the sendmail MTA should be ok since both exim and postfix
have sendmail compatable binaries/symlinks/etc.
** - I don't know what it is with the smail MTA, but for some reason *all*
mail gets lost during the internal transfers from the system mailbox
and back to the system mailbox. Since smail has basically been
abandoned in favor of exim, I don't personally foresee this as an
issue.
***- I've never installed a qmail system before and honestly don't feel
like doing that now hi!.. so if you run qmail and it works ok, please
let me know and I'll change it's status
If there's an MTA that I have missed and you've tested it and it works
please inform me and I'll add your results here.
How to test axmail:
You can run axmail at a command prompt!.. all it requires is that you put
your callsign after it. BEFORE you run this via a commandline however I
strongly suggest you make a backup of your system mail spool file by
typing: cp /var/spool/mail/call /var/spool/mail/call.bak this way here if
there is an issue and you have mail waiting, you won't lose any mail.
I'll assume your account on your box is your callsign, so in my case I would
execute:
n1uro@nat-client0:~$ /usr/sbin/axmail n1uro
and the standard greetings should appear along with the prompt and any
mail waiting should appear listed.
Pending the above test worked ok and unread/undeleted mail was saved back
into the system mailbox, try it from the node as a user who doesn't have
an account on the box. Hopefully when you exit, it'll tell you that you
have new mail waiting! Go back in and you should see the welcome.txt file
from /etc/ax25 listed as a greeting email message.
Other quick FAQs:
axMail works by comparing the user's system mail spool file, and as well
as any existing axMail saved mail and merges them together 'offline' for
lack of a better word to use. It then takes this mail and allows the user
to read/reply/delete/save/etc.
axMail has *always* supported file attachments, after all a file attachment
is just an encoded file appended to the body of the email message... its just
that most every client now-a-day automatically encodes/decodes them for you
and you assume that a file attachment is a seperate entity. All you need to
do to send and receive attachments via a packet terminal is the following
(examples taken from a linux terminal);
Sending: First encode the file by using uuencode. To do this run
uuencode filename filename
or if you want to make a file of it run: uuencode file file > file1
then copy and paste that encoded text in it's full into the body of
the mail message and send it.
Receiving: copy and paste the output of your message into a temporary
file and then run "uudecode -o filename tempfile". You will now have
a pdf/doc/text/jpg file sent to you by someone.
axMail now supports sending of fax transmissions! To configure axMail to
be able to do such, configure an account with an online fax service such
as eFax where you can email faxes and put the email address you'd use to
send faxes to in a _new line_ called "FaxGate" inside /etc/ax25/axmail.conf.
When users attempt to send a fax, your account will be hidden from them and
all they'll see is that they're sending to "a" fax gateway system.
People have asked about why new incoming mail isn't seen until after the
user logs out of axMail. If axMail read directly off of the system
mailspool file, then it'd lock out any new incoming mail from being posted
to the user's mailbox as it'd have a lock on the spool file, and the
message numbers could also possibly change while the user goes to select a
message number to read. This would be very confusing to the end user.
If you wish to allow users to use the internet or packet TCP/IP to pop3
their mail from your system, they may do so... however keep in mind, any
mail they read or list manually within axMail will have it's status
changed from "new". As we all know about the pop3 protocol, mail not
flagged as "new" isn't popped but it's considered as if the client is
using a software package such as eudora or outlook (to name a couple...
notice which I listed first? hi!) and they have their options set to leave
a copy of their mail on the server. The user will have to log into your
node and retrieve their mail from there. After all, isn't part of running
packet node services is to encourage hams to actually use their radios to
get to such things? :) All you as sysop/root on the box need to do is
ensure that a pop3 daemon is installed and running, and that you configure
axMail.conf to give the end user proper permissions in their shell to be
able to use your pop3 daemon.
I've gone to many days worth of studying how most boxes are configured
I've taken it upon myself to try and get axMail as 'bullet proof' and as
simple a process as it can possibly be. Unfortunately the program can not
read your mind so you'll have to do *some* config work to it... but
otherwise it should be a nice low-ram low-resource system for you and your
users to enjoy.
Comments and questions are always welcomed!
73 de Brian N1URO